AirSmart EcoConnect banner

Fresh Air When the Room Needs It

with AirSmart EcoConnect

Colour Display

Large, high-res colour display

Real Time Data

Real-time data for CO₂, temperature, humidity, lighting and sound levels

Outputs and relay

Two 0 to 10 V outputs and a relay to run your unit

Wi-Fi

Wi-Fi connectivity, no ongoing costs

Mobile App

Off, On and Auto modes, set in the AirSmart app

Web Portal

Web portal with reporting

Notifications

Customisable notifications

Building systems

Modbus and BACnet over RS-485 for building systems

AirSmart EcoConnect on a light background, its screen showing the sound level.

Introducing AirSmart EcoConnect

The Monitor That Runs Your Ventilation

AirSmart EcoConnect is AirSmart Edu with a control board. It measures the air and runs your fan, heat recovery unit or damper to match, so fresh air comes in when the room needs it.

Fresh Air Without Anyone Having to Remember

In a New Zealand winter, an open window means a cold room. In a 2015 study of 40 Auckland schools, only 40 % of teachers opened windows, and from April to October classroom windows tended to stay shut (Massey University, 2016). EcoConnect brings fresh air in for you.

More Fresh Air as the Room Fills

The outputs follow the CO₂, temperature or humidity in the room: more fresh air as it fills, less as it empties, never below the minimum you set.

See It Working

Every reading, with each output’s level and mode, reaches the AirSmart app and web portal every 15 minutes.

Two example settings. Control: the output holds a 30 % minimum, then follows CO₂ from 0 % at 800 ppm to 100 % at 1,200 ppm, so it rises above the minimum from 920 ppm. Transmit: the output rises from 0 V at 400 ppm to 10 V at 1,000 ppm, so 700 ppm gives 5 V.

You Choose How Each Output Runs

Off: the output stays at the bottom of its range.

On: a fixed level you choose, from 0 to 100 %, to override from the app.

Auto: the output follows temperature, humidity or CO₂ in a straight line between two set points. You choose whether it rises as the reading climbs or as it falls.

Each output can run a unit, with a minimum it never drops below, or send a reading to a building controller. The relay switches at set points you choose.

Your settings are stored on EcoConnect, so it keeps running your ventilation if the Wi-Fi goes down. It keeps logging too: readings are stored and sent when the connection comes back, so a temporary outage loses no data.

How AirSmart EcoConnect connects: the host unit or a building supply powers EcoConnect with 24 volts AC or 6 to 36 volts DC; EcoConnect sends 0 to 10 volt control signals and switches a relay back to the host unit; readings and settings travel over Wi-Fi between EcoConnect and the Monkeytronics cloud, which feeds the app and the web portal; a building management system can read EcoConnect over RS-485 using Modbus RTU or BACnet MS/TP.

Works With Your Fan, Heat Recovery Unit or Damper

EcoConnect works with fans, heat recovery units and dampers that take a 0 to 10 V signal. Its relay switches units that have an on and off input.

It runs on 24 V AC or 6 to 36 V DC, from the unit or a building supply. It connects to 2.4 GHz Wi-Fi that uses a network name and password, not a sign-in page.

Not sure about your unit? Email its make and model, or a photo of its label, to contact@monkeytronics.co.nz and Al will get back to you.

How EcoConnect will run a heat pump, on the roadmap: at set-up the user presses power once on their own remote, pointed at EcoConnect; from then on EcoConnect sends every command to the heat pump by infrared, as the remote would; EcoConnect measures the room at 1.5 m; readings, settings and the schedule travel over Wi-Fi to the Monkeytronics cloud, the app and the web portal.

On the Roadmap

What’s Coming to EcoConnect

Your heat pump measures the temperature up near the ceiling. AirSmart EcoConnect measures the temperature, humidity and CO₂ concentration as you feel it in the room. We are adding heat pump control by infrared, so EcoConnect can run your heat pump from those readings, the way its remote does.

Here’s the idea. EcoConnect can make decisions that will improve how you heat the spaces in your home. For example, you can ask it to switch the heat pump on as people arrive and off as they leave, based on CO₂ concentration; correct the set point from the temperature in the room; switch to dry mode when the room gets damp; run a 7-day schedule you set in the app or web portal.

We plan to support most heat pumps that come with an infrared remote.

Available now

Two 0 to 10 V outputs and a relay
CO₂, temperature, humidity, light and sound
Wi-Fi, the AirSmart app and web portal

By firmware update

Modbus RTU and BACnet MS/TP over RS-485
The first units may ship before this firmware and receive it by update

On the roadmap

Heat pump control by infrared
BACnet/IP and Modbus TCP over Wi-Fi

mobileappforinstallers

For Electricians and Ventilation Installers

Wire the Plug,
Then Push It In

The field wiring lands on one 8-way plug-in screw terminal: +V, 0 V, D1 (B, +), D0 (A, -), OUT1, OUT2, RLY and RLY. Wire the plug in the hand with 26 to 16 AWG wire, then push it into the back of EcoConnect. The unit hangs on two wall screws set with a 3D printed installation guide, so it sits flush and nothing else stays on the wall. Every terminal is designed to survive 24 V AC on any other terminal.

  • Scan the QR code with the AirSmart Installer app and connect to Wi-Fi

  • Set each output, the relay and the set points in the AirSmart app

  • Transfer the site to its owner when you are done

Power: 1 W typical, 2 W maximum. Allow 3 VA per unit on a 24 V AC transformer.

A qualified installer should do the wiring. We help commission every project.

AirSmart EcoConnect

Frequently Asked Questions

Will it work with my unit?

Yes, if it is a fan, heat recovery unit or damper that takes a 0 to 10 V signal. A unit with an on and off input works through the relay. Not sure? Email the make and model, or a photo of the label, to contact@monkeytronics.co.nz and Al will get back to you.

Can it run my heat pump?

Today, through the relay, if your heat pump has a maker’s contact adaptor or thermostat input. Heat pump control by infrared is on our roadmap.

Does it work with a building management system?

Yes. A building system can read every reading, both output levels, the modes and the relay over RS-485, as Modbus RTU or BACnet MS/TP (read access, no writes). EcoConnect can also send a reading to a building controller as a 0 to 10 V signal, for example 0 V at 400 ppm and 10 V at 1,000 ppm.

What power does it need?

24 V AC, or 6 to 36 V DC, from the unit it runs or from a building’s 24 V supply. It draws about 1 W, 2 W at most. Heat pump control by infrared (roadmap) will also need 5 V USB power at the unit.

Will the fresh air stop when the room empties?

Not unless you set it to. In control mode each output has a minimum you set, and the fan never drops below it. Set it to at least the unit’s design minimum airflow.

What happens if the Wi-Fi or the power goes off?

If the Wi-Fi goes down, EcoConnect keeps running your ventilation from its own readings and settings. It keeps logging too, and sends the stored readings when the connection comes back, so a temporary outage loses no data. After a power cut it starts up again with the same settings. During a firmware update the outputs hold their last value.

Will it lower my power bill?

EcoConnect doesn’t make fresh air free, but it stops a fan running flat out when the room doesn’t need it. In our model of a Wellington classroom, that avoids about 30 % of the heat used to warm the fresh air, about $32 per classroom each winter. That figure is modelled: we have not yet measured EcoConnect’s savings.

Are there ongoing costs?

No. The cloud, app and web portal are free for the life of the product, within fair-use limits. Custom add-ons are quoted separately.

Can a school use it as its classroom monitor?

NZSPA’s Designing Quality Learning Spaces (DQLS) says project teams must source all internal environmental monitoring devices from NZSPA. EcoConnect is AirSmart Edu with a control board, so it is approved as a monitoring device on the same basis as AirSmart Edu. Talk to us about your project.

Can I upgrade my AirSmart Edu?

No. EcoConnect is a separate product with its own control board, and there is no upgrade kit.

Who installs and sets it up?

A qualified installer should do the wiring. Then you set each output, the relay and the set points in the AirSmart app, and we help commission every project.

white-minimalistic-background-product-presentation
AirSmart EcoConnect

AirSmart EcoConnect

£439.00 + VAT