Fresh Air When the Room Needs It
with AirSmart EcoConnect
Large, high-res colour display
Real-time data for CO₂, temperature, humidity, lighting and sound levels
Two 0 to 10 V outputs and a relay to run your unit
Wi-Fi connectivity, no ongoing costs
Off, On and Auto modes, set in the AirSmart app
Web portal with reporting
Customisable notifications
Modbus and BACnet over RS-485 for building systems

Introducing AirSmart EcoConnect
The Monitor That Runs Your Ventilation
AirSmart EcoConnect is AirSmart Edu with a control board. It measures the air and runs your fan, heat recovery unit or damper to match, so fresh air comes in when the room needs it.
Fresh Air Without Anyone Having to Remember
In a New Zealand winter, an open window means a cold room. In a 2015 study of 40 Auckland schools, only 40 % of teachers opened windows, and from April to October classroom windows tended to stay shut (Massey University, 2016). EcoConnect brings fresh air in for you.
More Fresh Air as the Room Fills
The outputs follow the CO₂, temperature or humidity in the room: more fresh air as it fills, less as it empties, never below the minimum you set.
See It Working
Every reading, with each output’s level and mode, reaches the AirSmart app and web portal every 15 minutes.

You Choose How Each Output Runs
Off: the output stays at the bottom of its range.
On: a fixed level you choose, from 0 to 100 %, to override from the app.
Auto: the output follows temperature, humidity or CO₂ in a straight line between two set points. You choose whether it rises as the reading climbs or as it falls.
Each output can run a unit, with a minimum it never drops below, or send a reading to a building controller. The relay switches at set points you choose.
Your settings are stored on EcoConnect, so it keeps running your ventilation if the Wi-Fi goes down. It keeps logging too: readings are stored and sent when the connection comes back, so a temporary outage loses no data.
Reliable and Accurate Monitoring
The CO₂, temperature and humidity figures are from the Sensirion SCD30 datasheet, at 25 °C.





Made for Rooms Where People Come and Go

Classroom

Cafeteria

Library

Gym

Science Lab

Staff Room

Office

Works With Your Fan, Heat Recovery Unit or Damper
EcoConnect works with fans, heat recovery units and dampers that take a 0 to 10 V signal. Its relay switches units that have an on and off input.
It runs on 24 V AC or 6 to 36 V DC, from the unit or a building supply. It connects to 2.4 GHz Wi-Fi that uses a network name and password, not a sign-in page.
Not sure about your unit? Email its make and model, or a photo of its label, to contact@monkeytronics.co.nz and Al will get back to you.

On the Roadmap
What’s Coming to EcoConnect
Your heat pump measures the temperature up near the ceiling. AirSmart EcoConnect measures the temperature, humidity and CO₂ concentration as you feel it in the room. We are adding heat pump control by infrared, so EcoConnect can run your heat pump from those readings, the way its remote does.
Here’s the idea. EcoConnect can make decisions that will improve how you heat the spaces in your home. For example, you can ask it to switch the heat pump on as people arrive and off as they leave, based on CO₂ concentration; correct the set point from the temperature in the room; switch to dry mode when the room gets damp; run a 7-day schedule you set in the app or web portal.
We plan to support most heat pumps that come with an infrared remote.
Available now
Two 0 to 10 V outputs and a relay
CO₂, temperature, humidity, light and sound
Wi-Fi, the AirSmart app and web portal
By firmware update
Modbus RTU and BACnet MS/TP over RS-485
The first units may ship before this firmware and receive it by update
On the roadmap
Heat pump control by infrared
BACnet/IP and Modbus TCP over Wi-Fi
Specifications



For Electricians and Ventilation Installers
Wire the Plug,
Then Push It In
The field wiring lands on one 8-way plug-in screw terminal: +V, 0 V, D1 (B, +), D0 (A, -), OUT1, OUT2, RLY and RLY. Wire the plug in the hand with 26 to 16 AWG wire, then push it into the back of EcoConnect. The unit hangs on two wall screws set with a 3D printed installation guide, so it sits flush and nothing else stays on the wall. Every terminal is designed to survive 24 V AC on any other terminal.
Scan the QR code with the AirSmart Installer app and connect to Wi-Fi
Set each output, the relay and the set points in the AirSmart app
Transfer the site to its owner when you are done
Power: 1 W typical, 2 W maximum. Allow 3 VA per unit on a 24 V AC transformer.
A qualified installer should do the wiring. We help commission every project.
AirSmart EcoConnect
Frequently Asked Questions
Will it work with my unit?
Yes, if it is a fan, heat recovery unit or damper that takes a 0 to 10 V signal. A unit with an on and off input works through the relay. Not sure? Email the make and model, or a photo of the label, to contact@monkeytronics.co.nz and Al will get back to you.
Can it run my heat pump?
Today, through the relay, if your heat pump has a maker’s contact adaptor or thermostat input. Heat pump control by infrared is on our roadmap.
Does it work with a building management system?
Yes. A building system can read every reading, both output levels, the modes and the relay over RS-485, as Modbus RTU or BACnet MS/TP (read access, no writes). EcoConnect can also send a reading to a building controller as a 0 to 10 V signal, for example 0 V at 400 ppm and 10 V at 1,000 ppm.
What power does it need?
24 V AC, or 6 to 36 V DC, from the unit it runs or from a building’s 24 V supply. It draws about 1 W, 2 W at most. Heat pump control by infrared (roadmap) will also need 5 V USB power at the unit.
Will the fresh air stop when the room empties?
Not unless you set it to. In control mode each output has a minimum you set, and the fan never drops below it. Set it to at least the unit’s design minimum airflow.
What happens if the Wi-Fi or the power goes off?
If the Wi-Fi goes down, EcoConnect keeps running your ventilation from its own readings and settings. It keeps logging too, and sends the stored readings when the connection comes back, so a temporary outage loses no data. After a power cut it starts up again with the same settings. During a firmware update the outputs hold their last value.
Will it lower my power bill?
EcoConnect doesn’t make fresh air free, but it stops a fan running flat out when the room doesn’t need it. In our model of a Wellington classroom, that avoids about 30 % of the heat used to warm the fresh air, about $32 per classroom each winter. That figure is modelled: we have not yet measured EcoConnect’s savings.
Are there ongoing costs?
No. The cloud, app and web portal are free for the life of the product, within fair-use limits. Custom add-ons are quoted separately.
Can a school use it as its classroom monitor?
NZSPA’s Designing Quality Learning Spaces (DQLS) says project teams must source all internal environmental monitoring devices from NZSPA. EcoConnect is AirSmart Edu with a control board, so it is approved as a monitoring device on the same basis as AirSmart Edu. Talk to us about your project.
Can I upgrade my AirSmart Edu?
No. EcoConnect is a separate product with its own control board, and there is no upgrade kit.
Who installs and sets it up?
A qualified installer should do the wiring. Then you set each output, the relay and the set points in the AirSmart app, and we help commission every project.


Shop AirSmart
Explore our full range of AirSmart and Sensor Node monitors.







